国产高清精品亚洲一区二区三区_国产AV无码一区二区三区日韩_香焦一区二区三区在线现看_特级毛片久久精品_国产一区二区三区野外_天天躁日日躁狠狠躁无码_国产毛片精品大全_亚洲成在人网站无码天堂_啊灬啊灬啊灬快高潮视频_精品中文白虎无码

型號

包裝規(guī)格

每箱數(shù)量

產(chǎn)品代號

Permatex Sensor Safe Blue RTV Silicone Gasket is a single

component, room temperature vulcanizing gasketing

compound designed to provide reliable “formed-in-place”

gaskets for mechanical assemblies. This material cures on

exposure to moisture in the air to form a tough, flexible,

silicone rubber gasket. The product resists aging, weathering

and thermal cycling without hardening, shrinking or cracking.

The original "Blue" gasketing product, refined and oxygen

sensor safe.

PRODUCT BENEFITS

● Superior adhesion and flexibility

● Sensor safe

● Replaces most cut gaskets

● Can be used as a gasket maker or dressing

● Easy application

● Non-flammable, Non-toxic

TYPICAL APPLICATIONS

Gasket maker for flexible flanges, Use as a sealant to coat

any precut gasket.

DIRECTIONS FOR USE

For assembly as a form-in-place gasket

1. Remove all previous material from mating surfaces.

   Permatex Gasket Remover is recommend for most

   materials, not for plastics or painted surfaces.

2. For bes results, clean and dry all surfaces with a re

   sidue-free solvent, such as Permatex Brake and

   Parts Cleaner.

3. Cut nozzle to desired bead size,1/6 ti 1/4 in diame

   ter. A 1/8 bead is usually sufficient for most applic

   ations.

4. Remove cap, puncture tube or cartridge seal and attach

   extension nozzle.

5. Apply a continuous and even bead of silicone to one

   surface, first tracing the internal areas of the gasket

   configuration, then all surrounding bolt holes as shown

   below.

6. Assemble parts immediately while silicone is still wet.

7. Finger tighten flange only until material begins to seep

   out the sides of the flange.

8. Allow to set for at least two hours and re-torque at lease

   one quarter to one half tum.

9. For best results, allow to cure overnight.

   
   

For assembly as a gasket dressing

1. Repeat steps 1 thru 4 as in previous section.

2. Apply a thin film of silicone to one surface to be sealed.

3. Place the pre cut gasket onto silicone film.

4. Apply a second thin to pre-cut gasket surface.
   

5.Remove any excess and assemble parts immediately.

Note:Product not recommended for use as a cylinder

head gasket or head gasket sealant.

Instructions for PowerBead

1. Clean and dry all flange surfaces to be sealed.

2. Remove black cap from top of extension nozzle.

3. Turn nozzle extension one complete turn(360)

   counterclockwise.

4. Depress finger trigger and apply a continuous 1/16 inch

   to 1/8 inch PowerBead to one surface.

5. Assemble parts immediately while silicone is still wet.

6. Finger tighten flange only until material begins to seep

   out the sides of the flange.

7. Allow to set for at least two hours and re-torque at least

   one quarter to one half turm.

8. For best results, allow to cure overnight.

9. To close ,turn extension nozzle clockwise until tight

10. (about one full turn). Wipe off excess material from

    nozzle and replace black cap.

    
    

Storage of Unused Product

1. Create a"Silicone Plug" by allowing excess material to
   

   extend beyond the extension nozzle or aerosol tip to

   cure, sealing and protecting the remaining product from

   moisture, For reuse, simply remove the cured product

   from the tip.

2. For PowerBead dispensers, you may store remaining

   product using either the above "silicone plug" method or

   using the included plastic cap.

For Cleanup

1. Remove uncured product from parts and hand-tools

   with Permatex Envirosafe ODC Free

   Cleaner/Degreaser. If skinned over, break film with a

   dry cloth to remove as much as possible. Remove the

   remaining material with Permatex Gasket Remover.

2. Clean hands with a dry cloth or Permatex Fast 

   Orange hand cleaner.

PROPERTIES OF UNCURED MATERIAL

                                                       Typical Value

Chemical Type                       Acetoxy silicone rubber

Appearance                              Blue non-sag paste

Odor                                            Mild acetic acid

Specific Gravity                                       1.3

Extrusion rate@ 25℃（grams/min）      350

Flash Point ℃（℉  ）                             〉93（〉200）